CS 452/652 Winter 2020 - Assignment 0
(Version: Jan 6 10:05:19)
Due Date: Mon, Jan 13, 2020, 10:00am
In this assignment you will familiarize yourselves with the basic functionality of the TS-7200 board, its ARM CPU and the train controller, while learning techniques for handling asynchronous events by polling. It is recommended that you first write, compile, and execute several simple programs for the TS-7200, and only then start working on the assignment.
Write a program that runs on the TS-7200 system. Your program interacts with the user via the virtual terminal while controlling the following independent real-time activities:
The monitor should use cursor addressing (using appropriate ASCII sequences for terminal control) to display on its screen at least the following:
- a digital clock showing minutes, seconds, and tenths of seconds, which measures time accurately, in the sense that it does not slow down or lose ticks,
- a command line interface to the track that sets train speeds and switches turn-outs, and
- a real-time display on the terminal showing the state of the track.
These four components should be organized so that the display is easy to understand.
- the current time,
- a table of switch positions,
- a list of the most recently triggered sensors, and
- a prompt at which the user can type commands.
The command line interface should support, at a minimum, the following commands.
Use the EP9302's built-in 32-bit timer to implement the clock. Do not use interrupts.
- tr <train number> <train speed> – Set any train in motion at the desired speed (0 for stop).
- rv <train number> – The train should reverse direction. To reverse direction set the train speed to zero, wait until the train stops, send the reverse direction command, then send a speed command to re-accelerate the train. The assumption is that the train will go the same speed in reverse as it was going forward before the command. Do not send the reverse direction command before the train has stopped!
- sw <switch number> <switch direction> – Throw the given switch to straight (S) or curved (C). Make sure you can reliably communicate with the track and train hardware before attempting to throw switches. IMPORTANT: A solenoid must be switched off (via Command 0x20) between 100 and 500 milliseconds after it was activated! Also, do not under any circumstances activate a switch over and over again. Doing so will burn out the solenoid!
- q – halt the system and return to RedBoot.
Your program should be written as a polling loop, using output port COM1 to talk to the train set, and output port COM2 to talk to the terminal. (This is the default configuration and you should always leave it so.) The clock should not lose time.
Possibly Helpful Comments
It is strongly recommended to use the headlight on the trains as an easy method for telling if your commands to the trains are successful. Also, the headlights provide an indication of the current travelling direction of a train.
It should not be necessary to use the Märklin 6021 manual control box other than the 'stop' and 'go' buttons (stop+go = reset).
The workstations have three serial ports. You can run two gtkterm terminals, with one set to the characteristics of the train interface. In that way you can separate a hard problem, ‘Is the problem that the UART transmits incorrectly or that my train commands are incorrect?’ into two simple problems.
If you are using functions from the example bwio library for anything except debugging you are probably doing the assignment incorrectly.
For this assignment only, do not use compiler optimization!
There is a deliberately introduced bug in one of the bwio functions.
The assignment must be completely individually. Hand in the following, nicely formatted and printed.
Three examples of highly rated documentation from previous years:
- A description of how to access, make, and operate your program, including the full pathname of your executable file which we will download for testing.
- A description of the structure of your program. We will judge your program primarily on the basis of this description. Describe which algorithms and data structures are used and why you chose them. This description should include a list of unimplemented aspects of the assignments, if any. Also, if you know of bugs in your implementation describe them explicitly.
- Answers to the following questions:
- How do you know that your clock does not miss updates or lose time?
- How long does the train hardware take to reply to a sensor query? (Note: To answer these questions, you need to perform and report some timing of your polling loop.)
- You should have a code repository on UW's git server git.uwaterloo.ca containing the source code of your assignment, instructions how to make the executable, and the PDFs containing the descriptions of your program and answers to the questions above. The code and documentation must remain unmodified after submission until the assignments have been marked. Email the commit SHA to the instructor before the deadline. The repository must be set to 'Private' with TAs and instructor added as 'Reporter'.
- Make sure (test!) that the following sequence of operations results in a successful build of your program in the linux.student.cs environment. Make it clear in README.md where to find the documentation and executable!
git clone <your repo>
git checkout <commit hash>